Zasady działu: Kliknij, aby przejrzeć zasady tego działu
- Tytuł wątku powinien zawierać markę i pełny model sprzętu oraz skrótowy opis usterki.
- Treść wątku powinna zawierać dokładny opis usterki, co zostało sprawdzone/wymienione/zmierzone, wyniki tych działań, oznaczenie kodowe PCB (w przypadku napraw hardware) oraz sformułowane pytanie. W przypadku problemów z odczytaniem oznaczenia kodowego PCB, należy przeczytać TEN WĄTEK. Jeśli nadal nie można znaleźć oznaczenia, należy zamieścić wyraźne zdjęcia obu stron płyty - należy przy tym usunąć wszelkie folie i moduły, mogące ewentualnie zasłaniać oznaczenia płyty.
- Przed napisaniem nowego tematu, każdy użytkownik zobowiązany jest zapoznać się z wątkami w dziale SZKOLENIA i na ich podstawie dokonać próby wstępnej diagnostyki uszkodzenia.
- Nie jest dozwolone umieszczanie załączników w postaci kompletnych dokumentacji, a także jakichkolwiek wsadów BIOS / firmware (do tego służy dział PLIKI BIOS DO WERYFIKACJI). Dozwolone jest wyłącznie umieszczenie fragmentu dokumentacji, który ułatwi autorowi diagnostykę/naprawę sprzętu z wątku. W jednym poście można zamieścić nie więcej, niż jedną stronę instrukcji/schematu. Plik nie może posiadać widocznych znaków wodnych, napisów "confidential", adresów email etc.
- Nie jest dozwolone zamieszczanie linków do plików, znajdujących się na innych stronach internetowych.
- Nie jest dozwolone zakładanie tematu, który opisuje usterkę więcej niż jednego sprzętu. W takich przypadkach należy utworzyć osobne wątki dla każdego sprzętu.
- Nie jest dozwolone pisanie tematu lub postu, mającego charakter zapytania o schemat, boardview, zdjęcia płyty, wsad BIOS lub instrukcję serwisową. Do takich zapytań służy dział ZAPYTANIA O DOKUMENTACJE/BIOS.
Re: Re: Asus X515E - brak podświetlenia matrycy
przez Google Adsense [BOT] • 16 czerwca 2025, 21:54
There is no fuse used at this location for no reason. The fuse provide over current and short circuit protection.
In this case the fuse protect the motherboard and LVDS cable in case the LCD screen goes bad and also protect the motherboard and LCD screen in case the LVDS cable goes bad.
0Ω resistor is not a fuse and acts differently. It's true that it can blow if the current is exceeded, but this current is much greater then the rated current of this fuse. It also reacts much slower compared to a fuse. For the reasons stated, the 0Ω resistor offers only a very limited level of protection.
Copper wire is also not a fuse, but behaves similarly under overload with a difference in a response time. But provided that the copper wire used is of appropriate cross-section. For these reason, copper wire offers a limited level of protection.
How you replace this fuse is up to you, but a new fuse costs 1-2 zlotys, which is practically nothing compared to the price of the board.
If you are going to use wire anyway, let me emphasize again that the cross-section of the used wire is crucial.
In this case the fuse protect the motherboard and LVDS cable in case the LCD screen goes bad and also protect the motherboard and LCD screen in case the LVDS cable goes bad.
0Ω resistor is not a fuse and acts differently. It's true that it can blow if the current is exceeded, but this current is much greater then the rated current of this fuse. It also reacts much slower compared to a fuse. For the reasons stated, the 0Ω resistor offers only a very limited level of protection.
Copper wire is also not a fuse, but behaves similarly under overload with a difference in a response time. But provided that the copper wire used is of appropriate cross-section. For these reason, copper wire offers a limited level of protection.
How you replace this fuse is up to you, but a new fuse costs 1-2 zlotys, which is practically nothing compared to the price of the board.
If you are going to use wire anyway, let me emphasize again that the cross-section of the used wire is crucial.
krzysztof000 napisał(a):Charakterystyka bezpiecznika: superszybkiThis could be a problem, as it could happen that such a fuse would react too quickly and blow for no particular reason due to the inrush current.
A standard fast acting fuse is originally used here.
Do you have a part number or data sheet of this fuse?
Re: Asus X515E - brak podświetlenia matrycy
przez Google Adsense [BOT] • 17 czerwca 2025, 10:50
Kto przegląda forum
Użytkownicy przeglądający ten dział: Brak zidentyfikowanych użytkowników i 4 gości
_______________________________Wszelkie prawa zastrzeżone. Zabrania się kopiowania jakichkolwiek treści i elementów witryny bez zezwolenia.
Wszelkie opublikowane na tej stronie znaki handlowe, nazwy marek, produktów czy usług należą do ich prawnych właścicieli i zostały użyte wyłącznie w celach informacyjnych.