HP Pavillon Gaming 16-a0034nw (DAG3JBMB8D0) - brak podświetlenia matrycy

Witam,
pacjent jak w temacie. Treść jest, podświetlenia brak - doświadczenie kazało sprawdzić bezpiecznik od zasilania matrycy, który wygląda w porządku jednak napięcie wydaje mi się ciut małe bo tylko ~10,5V z obydwu stron F4502 i potrzebowałbym pomocy w namierzeniu usterki.

Hello!

Measure the voltages to ground on pins 1, 4, 5 of transistors PQ1002, PQ1003.

matic писал(а):Hello!

Measure the voltages to ground on pins 1, 4, 5 of transistors PQ1002, PQ1003.

Teraz zauważyłem jeszcze, że nie uruchamia się na samym zasilaczu i nie ładuje baterii. Czy może to być spowodowane tym, że nie mogę podać 7,7A?


Zasilacz + bateria :
F4502 - 19,5V
PQ1002:

N1 - 19,5V
N4 - 25,25V
N5 - 19,5V

PQ1003:

N1 - 19,5V
N4 - 25,25V
N5 - 19,5V

Sam zasilacz - to samo co wyżej

Sama bateria :
F4502 - 10,5V
PQ1002:

N1 - 0V
N4 - 0V
N5 - 10,5V

PQ1003:

N1 - 0V
N4 - 0V
N5 - impuls 2V i spada

EDIT:
Z oryg. zasilaczem ładuje baterię i się uruchamia, po podładowaniu na baterii pomiary identyczne F4502 i N5 PQ1002 = napięciu baterii, N5 PQ1003 dostaje impuls i spada, N4 i N1 0V

kuras00 писал(а):Teraz zauważyłem jeszcze, że nie uruchamia się na samym zasilaczu i nie ładuje baterii. Czy może to być spowodowane tym, że nie mogę podać 7,7A?

Did you use a properly prepared service DC cable with a resistor connected to the central pin?

kuras00 писал(а):jednak napięcie wydaje mi się ciut małe bo tylko ~10,5V z obydwu stron F4502

Was this measurement taken while the machine was running on the battery or the power supply?

matic писал(а):Did you use a properly prepared service DC cable with a resistor connected to the central pin?

Bez spreparowanego kabla. Mam już dostarczony oryginalny zasilacz i laptop się uruchamia + jest ładowanie.

matic писал(а):Was this measurement taken while the machine was running on the battery or the power supply?

Na baterii. Po naładowaniu na uruchomieniu z baterii jest 11,5V, z zasilacza 19,5V, zasilacz + bateria 19,5V - we wszystkich przypadkach brak podświetlenia (taśmę podstawiałem - bez zmian).

So this voltage is perfectly fine.
Measure the voltages to ground on pins 4, 5 of LVDS connector CN7000 while the machine is turned on with the matrix connected.

matic писал(а):Measure the voltages to ground on pins 4, 5 of LVDS connector CN7000 while the machine is turned on with the matrix connected.

P4 - 3,1V
P5 - 0,6V

kuras00 писал(а):P5 - 0,6V

And that's wrong.
Measure the resistances to ground on both pins of resistor R7008 with the matrix connected to the board.

matic писал(а):Measure the resistances to ground on both pins of resistor R7008 with the matrix connected to the board.

N1 - 91,9Ω
N2 - 90,9Ω
Sam rezystor wydaje się być w porządku - 1kΩ

Idąc dalej R7013 N1 i N2 91,9Ω, 10Ω

Następny zostaje PCH?

kuras00 писал(а):N1 - 91,9Ω
N2 - 90,9Ω
Sam rezystor wydaje się być w porządku - 1kΩ

That's quite strange.
- Measure the resistance to ground on pin 4 of LVDS connector CN7000 with the matrix connected.
- Measure the resistance to ground on any pin of resistor R7013 with the matrix connected.

matic писал(а):Measure the resistance to ground on pin 4 of LVDS connector CN7000 with the matrix connected.

70kΩ

matic писал(а):Measure the resistance to ground on any pin of resistor R7013 with the matrix connected.

kuras00 писал(а):Idąc dalej R7013 N1 i N2 91,9Ω, 10Ω

kuras00 писал(а):

matic писал(а):Measure the resistances to ground on both pins of resistor R7008 with the matrix connected to the board.

N1 - 91,9Ω
N2 - 90,9Ω

One of this two measurements is definitely wrong, otherwise the schematic I have is incompatible with your board.

kuras00 писал(а):Idąc dalej R7013 N1 i N2 91,9Ω

And also there can't be the same resistance on both pins of this resistor since the resistor value is 10Ω.

kuras00 писал(а):

matic писал(а):Measure the resistance to ground on pin 4 of LVDS connector CN7000 with the matrix connected.

70kΩ

Impossible since the value of resistor R7008 is 1kΩ and the resistance to ground on one side of this resistor is around 100Ω. Based on your measurements, I expect a maximum value of 1.1kΩ on this pin.

kuras00 писал(а):DAG3JBMB8D0

Please, check the motherboard marking code you specified is correct.

Post a clear picture of your board. Also post a picture of R7008/R7013 area of the board.

The schematic and BoardView seems to be compatible with your board.
You should taken the measurements on the wrong components/pins, otherwise there should be something wrong with your meter.

Check the continuity between pin 5 of LVDS connector and point "A".
If the continuity is fine, remeasure the resistances to ground on points "A", "B", "C" and pin 5 of LVDS connector.

Ciągłość jest.

A - 99,1kΩ
B - 100,1kΩ
C - 100,1kΩ
P5 - 99,1kΩ

That's completely different measurements, and the resistances seems fine now.

- Measure the voltage to ground at point "C" while the machine is turned on with the matrix connected.

matic писал(а):[ Obrazek ]

0,68V

Remove the resistor R7013 from the board and remeasure the voltage to ground at point "C" while the machine is turned on.
If the voltage is still below 1V, turn off the machine, disconnect the power supply and wait abut two minutes. Then set your multimeter to the diode test mode and measure the voltage drop to ground at point "C" with the positive (red) probe connected to ground.

Po zdjęciu R7013 dalej 0,68V

Pomiar diody 0,791V

Reflash the BIOS chip and check if anything changes. Don't forget to save the old dump.