• Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje

Forum rules:Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.

#1 Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 30 September 2025, 19:01
Cześć,
Przy podłączonej baterii oraz zasilaniu pobór prądu 47mA oraz świeci na niebiesko dioda przy gniazdku zasilania.
Napięcia na cewkach:
PL1 - 8v
L8 - 3.3v
L9 - 5v
L1 - 0v
L10 - 1.8v
L11 - 1.8v
L12 - 0 v
L13 - 0v

Nie mam schematu i nie wiem który pin idzie z włącznika w klawiaturze, ale jest na kilku pinach napięcie 3.3v i żadne nie zmienia się na 0v przy wciśkaniu klawisza power. Próbowałem przez rezystor zwierać te piny co mają 3.3v do masy ale brak reakcji. Wgrałem inny bios, nic to nie dało. Napięcie zasilania na kości bios jest obecne, obserwując oscyloskopem nóżki kości bios, na początku jest przez ułamek sekundy jakaś wymiana danych a potem już nic - stan wysoki. Rezystancja na cewkach bez napięcia L12,L13 dość wysoka - 47 oHm, co tutaj dalej począć?

Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by Google Adsense [BOT] 30 September 2025, 19:01

#2 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by Vogelek23 1 October 2025, 01:13
Zamieść wyraźne zdjęcia obu stron płyty (usuń przedtem wszelkie naklejki i folie, mogące zakrywać elementy).

#3 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 1 October 2025, 18:07
proszę bardzo, jak za słaba jakość to mogę próbować jeszcze po kawałku coś wydusić z tego mojego "szałomi"

Image

Image

Image

#4 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by matic 1 October 2025, 21:27
HotIce wrote:L10 - 1.8v
L11 - 1.8v
Are these two measurements correct?

Post a clear picture with visible markings on the chip U7 (it's located near the coil L1).

#5 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 4 October 2025, 16:32
matic wrote:Are these two measurements correct?


tak, to jest poprawny pomiar, L10 i L11 mają 1.8v.
Poniżej chip U7 w przybliżeniu:

Image

#6 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by matic 5 October 2025, 12:01
Measure the voltages to ground on pins 1, 3, 8, 10, 11, 12, 15, 16 of the chip U7.
Chip U7 pinout:
Image

#7 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 5 October 2025, 12:51
U7:
1 - 19v
3 - 3.3v
8 - 3.3v
10 - 2.9v
11 - 0v
12 - 0v
15 - 0v
16 - 0.03v

#8 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by matic 5 October 2025, 18:04
Set your multimeter to the diode test mode and measure the voltage drops to ground on pins 15, 16 of the chip U7 with the positive (red) probe connected to ground.

#9 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 5 October 2025, 21:10
matic wrote:Set your multimeter to the diode test mode and measure the voltage drops to ground on pins 15, 16 of the chip U7 with the positive (red) probe connected to ground.

spadek napięcia na pinach 15 oraz 16 to 0.58v

#10 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by matic 9 October 2025, 15:47
Use a continuity tester to check if pin 110 of the KBC chip is connected to any pin of the keyboard connector.

#11 Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by HotIce 9 October 2025, 16:36
matic wrote:Use a continuity tester to check if pin 110 of the KBC chip is connected to any pin of the keyboard connector.


Pomiędzy pinem 110 KBC nie ma przejścia na żaden pin złącza klawiatury.

Re: Toshiba C50-H-104 ,MB : IP3_IN16_MB_V21_20200831A - nie startuje


by Google Adsense [BOT] 9 October 2025, 16:36

Who is online

Users browsing this forum: No registered users and 0 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.