Forumsregeln: Die Forumsregeln lesen
- Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
- Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
- Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
- Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
- Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
- Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.
Re: Re: Asus X515E - brak podświetlenia matrycy
von Google Adsense [BOT] • 16 Juni 2025, 21:54
There is no fuse used at this location for no reason. The fuse provide over current and short circuit protection.
In this case the fuse protect the motherboard and LVDS cable in case the LCD screen goes bad and also protect the motherboard and LCD screen in case the LVDS cable goes bad.
0Ω resistor is not a fuse and acts differently. It's true that it can blow if the current is exceeded, but this current is much greater then the rated current of this fuse. It also reacts much slower compared to a fuse. For the reasons stated, the 0Ω resistor offers only a very limited level of protection.
Copper wire is also not a fuse, but behaves similarly under overload with a difference in a response time. But provided that the copper wire used is of appropriate cross-section. For these reason, copper wire offers a limited level of protection.
How you replace this fuse is up to you, but a new fuse costs 1-2 zlotys, which is practically nothing compared to the price of the board.
If you are going to use wire anyway, let me emphasize again that the cross-section of the used wire is crucial.
In this case the fuse protect the motherboard and LVDS cable in case the LCD screen goes bad and also protect the motherboard and LCD screen in case the LVDS cable goes bad.
0Ω resistor is not a fuse and acts differently. It's true that it can blow if the current is exceeded, but this current is much greater then the rated current of this fuse. It also reacts much slower compared to a fuse. For the reasons stated, the 0Ω resistor offers only a very limited level of protection.
Copper wire is also not a fuse, but behaves similarly under overload with a difference in a response time. But provided that the copper wire used is of appropriate cross-section. For these reason, copper wire offers a limited level of protection.
How you replace this fuse is up to you, but a new fuse costs 1-2 zlotys, which is practically nothing compared to the price of the board.
If you are going to use wire anyway, let me emphasize again that the cross-section of the used wire is crucial.
krzysztof000 hat geschrieben:Charakterystyka bezpiecznika: superszybkiThis could be a problem, as it could happen that such a fuse would react too quickly and blow for no particular reason due to the inrush current.
A standard fast acting fuse is originally used here.
Do you have a part number or data sheet of this fuse?
Re: Asus X515E - brak podświetlenia matrycy
von Google Adsense [BOT] • 17 Juni 2025, 10:50
Wer ist online?
Mitglieder in diesem Forum: 0 Mitglieder und 7 Gäste
_______________________________Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.