Samsung NP-RC710 Jinmao-L REV: 1.0 Nie włącza się.

Witam,
Model: Samsung NP-RC710
Płyta: Jinmao-L Rev: 1.0
KBC: MEC1300-NU
CPU: i3-380M (SLBZX)
GPU: N12M-GE-S-B1
Kość: MX 25L3206E


Laptop się nie uruchamia. Po podłączeniu zasilacza świeci zielona dioda. Po włączeniu przycisku "Power" brak jakiejkolwiek reakcji. 3.3V obecne na przycisku "Power".
Zmierzyłem rezystancje na cewkach.



1 - 400 kΩ
2 - 23 kΩ
3 - 5,8 kΩ
4 - 12,8 Ω
5 - 1,9 kΩ
6 - 30 Ω
7 - 30 Ω
8 - 44 Ω
9 - 7 Ω (koło mostka)

Na podłączonym zasilaczu napięcie tylko na celce "1" = 0,37 V.

Można prosić o pomoc?

Hello!

Measure the voltages to ground on pins 64, 116 of KBC chip in the following cases:
a) Power button released.
b) Power button pressed.

matic написав:Measure the voltages to ground on pins 64, 116 of KBC chip in the following cases:
a) Power button released.
b) Power button pressed.

Ad. a) pin 64 = 0,42 V, pin 116 = 3,3V
Ad. b) pin 64 = 0,42 V, pin 116 = 0V

- Measure the voltages to ground on pins 7, 8 of BIOS chip.
- Measure the voltages to ground on pins 4, 15, 33, 34, 40, 42, 43, 53, 65, 90, 107 of KBC chip.

matic написав:- Measure the voltages to ground on pins 7, 8 of BIOS chip.

pin 7,8 = 3,3 V

matic написав:- Measure the voltages to ground on pins 4, 15, 33, 34, 40, 42, 43, 53, 65, 90, 107 of KBC chip.

pin 4 = 0 V
pin 15 = 1,84 V
pin 33 = 0,12 V
pin 34 = 0,56 V
pin 40 = 3,3 V
pin 42 = 0 V
pin 43 = 0 V
pin 53 = 0,35 V
pin 65 = 0,54 V
pin 90 = 0 V
pin 107 = 0 V

Wymieniłem profilaktycznie przetwornicę TPS51125. Dalej bez zmian.
prośba o dalsze sugestie.

Measure the voltages on pin 116 of the KBC in the following cases:
to power OFF
with power on pressed
to power "ON".
If you took the measurements on the KBC without pressing the start button, remeasure them.

Machine написав:to power OFF

pin 116 = 3,3 V

Machine написав:with power on pressed

pin 116 = 0 V when preesed, after that presents again 3,3 V

Machine написав:to power "ON"

pin 116 = 3,3 V

Remeasure after pressed:
pin 4 = 0 V
pin 15 = 1,84 V
pin 33 = 0,12 V
pin 34 = 0,56 V
pin 40 = 3,3 V
pin 42 = 0 V
pin 43 = 0 V
pin 53 = 0,12 V
pin 65 = 0,54 V
pin 90 = 0 V
pin 107 = 0 V

Replace the bios and remember to save the old one.

Machine написав:Replace the bios and remember to save the old one.

I do not have any data in bios chip. It was empty. Strange...

I programed the dump from this post: samsung-rc710-czarny-ekran-t29763.html
Board turned on. The display is ok but fan have very high speed all the time.

When I cleaned the ME region, the board turned on but I have only backlight. In this case I do not have a video on the screen.

Bezel018 написав:When I cleaned the ME region, the board turned on but I have only backlight. In this case I do not have a video on the screen.

You have not successfully cleaned the ME-region, or you used an incompatible version of the ME-region.
You can upload the BIOS dump to the "ZAPYTANIA O DOKUMENTACJE/BIOS" department and ask for cleaning the ME-region. Don't forget to specify the major IC's markings according to the rules.

I found the working BIOS dump.
The fan working properly!
You can find it here: samsung-np-rc710-mb-samsung-jinmao-l-rev-1-0-czysty-me-region-t72409.html

Thanks all for help!