#1 Toshiba A300 motherboard QUANTA BL5S SANTA ROSA no +3VPCU and no +5VPCU
przez rafamsx • 29 lipca 2013, 22:09
Hola a todos! Este es mi primer post en este foro. Soy de España por lo que quizás cometa errores al traducir. Me dedico a reparar portátiles y espero aportar todo lo que pueda a este foro.
Tengo un TOSHIBA A300 con placa base QUANTA BL5S SANTA ROSA en los que no tengo ni +5VPCU ni +3VPCU.
He realizado las siguientes medidas en PU5 (ISL6237)
VIN = 19v
VCC = 4,96v
REF = 1,99v
LDO = 4,98v
EN1 = 4,95v
EN2 = 4,95v
PVCC=4,97v
También he testeado PQ9, PQ10, PQ11 y PQ13
Creo que los valores son correctos, para descartar he cambiado el ISL6237 y los valores que he medido son los mismos.
También he medido continuidad entre PL3 y PL4 con respecto a masa por si tenía algún cruce en esa línea, pero parece estar bien.
Me estoy volviendo loco con esta placa... Alguien me puede ayudar?
Gracias
Hello everyone! This is my first post in this forum. I'm from Spain so perhaps make mistakes when translating. I am dedicated to repairing laptops and I hope to contribute everything I can to this forum.
I have a Toshiba A300 with motherboard QUANTA BL5S SANTA ROSA where I have no +3VPCU and no +5VPCU.
I have made the following measures in PU5 (ISL6237)
VIN = 19V
VCC = 4.96 v
REF = 1.99 v
LDO = 4.98 v
EN1 = 4.95 v
EN2 = 4.95 v
PVCC = 4.97 v
I have also tested PQ9, PQ10, PQ11 and PQ13
I think the settings are correct, to discard I changed the ISL6237 and I have measured values are the same.
Also I measured continuity between PL3 and PL4 with respect to ground, no shorts, seems to be fine.
I'm going crazy with this board ... Someone can help me?
Thanks
Tengo un TOSHIBA A300 con placa base QUANTA BL5S SANTA ROSA en los que no tengo ni +5VPCU ni +3VPCU.
He realizado las siguientes medidas en PU5 (ISL6237)
VIN = 19v
VCC = 4,96v
REF = 1,99v
LDO = 4,98v
EN1 = 4,95v
EN2 = 4,95v
PVCC=4,97v
También he testeado PQ9, PQ10, PQ11 y PQ13
Creo que los valores son correctos, para descartar he cambiado el ISL6237 y los valores que he medido son los mismos.
También he medido continuidad entre PL3 y PL4 con respecto a masa por si tenía algún cruce en esa línea, pero parece estar bien.
Me estoy volviendo loco con esta placa... Alguien me puede ayudar?
Gracias
Hello everyone! This is my first post in this forum. I'm from Spain so perhaps make mistakes when translating. I am dedicated to repairing laptops and I hope to contribute everything I can to this forum.
I have a Toshiba A300 with motherboard QUANTA BL5S SANTA ROSA where I have no +3VPCU and no +5VPCU.
I have made the following measures in PU5 (ISL6237)
VIN = 19V
VCC = 4.96 v
REF = 1.99 v
LDO = 4.98 v
EN1 = 4.95 v
EN2 = 4.95 v
PVCC = 4.97 v
I have also tested PQ9, PQ10, PQ11 and PQ13
I think the settings are correct, to discard I changed the ISL6237 and I have measured values are the same.
Also I measured continuity between PL3 and PL4 with respect to ground, no shorts, seems to be fine.
I'm going crazy with this board ... Someone can help me?
Thanks