• monitor LG W1953TE no power , no led standby

Danes je 27 Junij 2025, 22:07

monitor LG W1953TE no power , no led standby

 Pravila foruma: Klikni tukaj za prikaz pravil na forumu

  1. Naslov teme mora vsebovati: proizvajalca naprave, poln model in kratek opis okvare.
  2. Sporočilo teme mora vsebovati: oznako tiskanega vezja (v primeru popravil strojne opreme), razširjen opis okvare, kaj je bilo preverjeno, zamenjano in/ali izmerjeno, sklep in vprašanje. Če ne morete najti oznake tiskanega vezja, morate prebrati TO TEMO. Če še vedno ne najdete oznake, prosim objavite kakovostne fotografije obeh strani matične plošče - potrebno je odstraniti vse folije in module, ki bi lahko zakrivali te oznake.
  3. Pred objavo nove teme, preberite vse teme v podforumu USPOSABLJANJA, in naredite predhodno diagnostiko na podlagi vsebine teh usposabljanj.
  4. Nalaganje celotnih navodil/shem, BIOS / firmware datotek, ali objavljanje povezav, ki vodijo do drugih spletnih strani s takšnimi datotekami, je SROGO PREPOVEDANO. Lahko objavite le majhen del navodil/shem, ali povezavo na BIOS datoteko v podforumu NEVERIFICIRANE DATOTEKE BIOS/EFI. V eni temi ne smete objaviti več kot eno stran navodil/shem. Datoteka ne sme vsebovati vidnih žigov "zaupno",, e-poštnih naslovov ipd.
  5. V eni temi lahko opišete SAMO eno napravo. Za vsako drugo okvarjeno napravo morate odpreti novo temo.
  6. Zahteve za sheme, boardview, fotografije matičnih plošč, datoteke BIOS-a ali servisne priročnike za storitve NISO DOVOLJENE. Če želite vprašati za katero koli od teh, odprite novo temo v podforumu ZAHTEVA ZA DOKUMENTACIJO & DATOTEKO BIOS/EFI.

#1 monitor LG W1953TE no power , no led standby

Napisal/-a eletmoraes • 22 Maj 2017, 23:53
voltage 12 and 5v --> OK
voltage 3.3v --> OK
Voltage on pin 3 of the UC601 (APE8839) of 5v when it should be 1.8v , located on the video card

Was rewritten the flash memory 25x20 without success. There is another memory located near the connector that goes to the front panel insert that I can not find the firmware to try to re-record. This memory is a 25C02 .
You would have to find the two firmware of this monitor to try to record these two memories.

Re: monitor LG W1953TE no power , no led standby

Napisal/-a Google Adsense [BOT] • 22 Maj 2017, 23:53

#2 Re: monitor LG W1953TE no power , no led standby

Napisal/-a matic • 23 Maj 2017, 21:47
Hello!

If the voltage on pin 3 of APE8839 is 5V that chip is probably burned. Yes, it should be 1.8V.
It is bad all other chips on 1.8V power supply line for sure.

#3 Re: monitor LG W1953TE no power , no led standby

Napisal/-a eletmoraes • 24 Maj 2017, 01:45
Hello, how are you . Before , measured the voltage on pin 3 of the APE8839mp and was supplying 5v, now after removing this component and testing it out and seeing that it is good I ended up soldering the APE8839mp on the video card. When I turned on the monitor, I measured the voltage on the same pin 3 of the APE8839, to my surprise the measured voltage was 1.8V.
Seeing that the basic and main voltages are correct the monitor still does not turn on.
:frustry:




It may be that have some cold solder in this integrated supplying this wrong voltage. What is important now is that the voltages in this component are correct.

#4 Re: monitor LG W1953TE no power , no led standby

Napisal/-a matic • 25 Maj 2017, 20:00
If you get 3.3V on pin one, and 1.8V on pin three of APE8839 this chip is good.

Measure the voltage on power button.

#5 Re: monitor LG W1953TE no power , no led standby

Napisal/-a eletmoraes • 26 Maj 2017, 14:46
Sorry friend, this monitor has no on-off button and yes touch, it connects with a finger touch.

#6 Re: monitor LG W1953TE no power , no led standby

Napisal/-a eletmoraes • 11 Julij 2017, 15:01
I was analyzing the video card better and compared to the monitor scheme, I found two smd resistors that
, Whether it exists or not. It would be the resistor R744 and R745 that on the board they do not contain them and, in the schematic, it is written as "Ready".


R744 ->? Does he exist or not?
R745 ->? Does he exist or not?

#7 Re: monitor LG W1953TE no power , no led standby

Napisal/-a eletmoraes • 12 Oktober 2017, 16:30
As the monitor owner was in a hurry of monitor , I had no choice but to replace the video card. After replacing the video card, the monitor returned to normal operation.

Re: monitor LG W1953TE no power , no led standby

Napisal/-a Google Adsense [BOT] • 12 Oktober 2017, 16:30
Podobne Teme
  Asus F541U turns on standby and power lights and nothing else MB X541UVK  [REŠENO]
PS4 Power Supply (ADP-240AR AA) - standby voltage is present, missing 12V
  Monitor 65" IIyama TE6502MIS (płyta tp.t972.470w) - brak reakcji na power
  Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else
Subwoofer JBL SUB125 - nie uruchamia się, ciągle świeci dioda "standby"
Monitor ASUS ROG PG259 - nie włącza się

Kdo je na strani

Po forumu brska: 0 registriranih uporabnikov in 0 gostov

_______________________________
Vse pravice pridržane. Nepooblaščeno kopiranje vsebine te spletne strani ali njenega dela je strogo prepovedano.
Vse blagovne znamke, izdelki ali storitve, objavljene na tej spletni strani, pripadajo njihovim zakonitim lastnikom, so avtorsko zaščitene in se uporabljajo samo v informativne namene.