• HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?

Forum rules:Click here to view the forum rules

  1. Topic title should contain the brief description of problem.
  2. Topic message should contain the extended description of problem and, the question.
  3. It is not allowed to post the attachments with complete documentations or BIOS files nor linking to any 3rd party websites hosting such files. It is only allowed to post the small portion of the documentation (up to one page per post).
  4. You can only describe one problem per topic. For each another problem you should open a new topic.
  5. It is strictly forbidden to ask for any kind of documentation or BIOS file. For such requests please use the DOCUMENTATION & BIOS/EFI REQUEST subforum.
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by cov 30 March 2017, 12:21
Witam

Mam płytę od HP DV6000 płyta DA0AT3MB8F0 wersja z grafiką 730. W płycie grzebana grafika, po zdjęciu grafiki okazało się że brakuje sporej ilości padów...
Przyszedł mi do głowy pomysł aby przerobić płytę z wersji z grafiką na wersję z integra ( z DSC na UMA ).
Na chwilę obecną wymieniłem mostek północny z wersji PM na GM, zmieniłem wersję BIOS, oraz przełożyłem rezystory:
RP59 na RP60
RP11 na RP54
RP56 na RP55
RP57 na RP58
RP3 na RP4
RP5 na RP6
RP9 na RP10
RP7 na RP8

Próbuję jeszcze namierzyć R42 ale nie mogę go znaleźć

Na razie cały czas nie ma efektów, pobór prądu to około 0,7A więc to jeszcze nie wszystko.
Niestety nie mam oryginalnej płyty integra do porównania, ktoś robił już taką modyfikację?

Pozdrawiam
Jacek

Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by Google Adsense [BOT] 30 March 2017, 12:21

#2 Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by finbar 30 March 2017, 12:44
cov wrote:Próbuję jeszcze namierzyć R42 ale nie mogę go znaleźć

Look this
Image

#3 Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by finbar 30 March 2017, 13:00
R760, R761, R692, R448, R690 are installed
R660, R652, R693, R688, R689 - removed
R287 rearrange to position R296
RP59, RP11, RP56, RP57, RP3, RP5, RP9, RP7 - take off
RP60, RP54, RP55, RP58, RP4, RP6, RP10, RP8 - install
R598, R174 - remove
R83 set 2,4k
R42 set to 255
R62, R66, R78, R74, R77, R65 - set 150 Ω
R64, R60 - set to 39 Ohm
R37 - install, R70 remove
L64 - install, R508, R509 - remove
L62, R499 - install, R515 - remove
R44 - set, R89 remove
R47 - set, R43 remove
L63, R504, R503, R502 - install, R511, R513, R514 - remove
R23, R501 - install, R512 - remove
R24 - set, R58 - remove
C652, C664, C657, C655, C656, C654, C665, C662, C661, C659, C947, C37, C32, C43, C945, C909, C668, C29, C653, C69 - set
Image
Image
Id is now 00101
Image

#4 Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by cov 31 March 2017, 14:57
Thanks a lot for instruction.

I have done all changes except:
C945- do not exist on schematic
C657,C659,C661,C662 - on diagram capacitors has 3 pins, and do not have any

Rest is done, but is no change, still power cosumption is around 0,7 A, I have plug diagnostic card and it show "00" and no change

Have you tried this change before? Is it was worked?

Thanks
Jacek

#5 Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by Vogelek23 31 March 2017, 20:06
cov wrote:Rest is done, but is no change, still power cosumption is around 0,7 A, I have plug diagnostic card and it show "00" and no change
Brak procedury POST - obawiam się, że problem może tkwić zupełnie gdzie indziej. Podstawiałeś CPU? Jak zachowywała się płyta przed przeróbką? Czy prąd był taki sam?

#6 Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by cov 3 April 2017, 08:43
Vogelek23 wrote:
cov wrote:Rest is done, but is no change, still power cosumption is around 0,7 A, I have plug diagnostic card and it show "00" and no change
Brak procedury POST - obawiam się, że problem może tkwić zupełnie gdzie indziej. Podstawiałeś CPU? Jak zachowywała się płyta przed przeróbką? Czy prąd był taki sam?


Jak płyta trafiła do mnie, to była z grzebaną grafiką z grubą warstwą zaschniętego topnika pomieszanego z resztkami kleju, a płyta uruchamiała się napięciowo, i zatrzymywała się na poście "B0" przy poborze prądu w okolicach 1,3A -1,5A. Po zdjęciu grafiki okazało się że ktoś tylko grzał układ bez jego ściągania, a klej z układu był ściągany razem z solder maską i ścieżkami, a z układem zeszło kilka padów. Niestety nie było szansy żeby odtworzyć wszystkie połączenia, stąd pomysł przeróbki. Na początek poszedł mostek północny (bez problemów, wszystkie pady na miejscu) oraz wszystko to co opisywałem w pierwszym poście, i od tego czasu pobór 0,7A. Nie podłączałem wtedy karty diagnostycznej, bo myślałem że niższy pobór wynika z braku uruchomienia karty graficznej. CPU podmieniony, ale bez zmian. Podmienię inny mostek dla pewności.


ed. podmiana mostka nie przyniosła żadnych zmian...

Re: HP DV6000 płyta DA0AT3MB8F0 modyfikacja z DSC na UMA ?


by Google Adsense [BOT] 3 April 2017, 08:43
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

Who is online

Users browsing this forum: No registered users and 3 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.