• Dell Latitude 7400 - brak podświetlenia po zalaniu

Regole del forum:Clicca per leggere le regole del forum

  1. Il titolo dell'argomento deve contenere: marca e modello completo del dispositivo e la breve descrizione del problema.
  2. Il messaggio di argomento dovrebbe contenere: un identificatore PCB (in caso di riparazioni hardware), descrizione estesa del problema, cosa è stato controllato/sostituito/misurato, eventuali conclusioni e la domanda. Se non riesci a individuare un identificatore PCB, leggi QUESTO ARGOMENTO. Se non riesci ancora a individuare un identificatore PCB, invia foto chiare di entrambi i lati della scheda madre; è necessario rimuovere qualsiasi pellicola o altri elementi che potrebbero coprire questo identificatore.
  3. Prima di pubblicare un nuovo argomento, leggere tutti gli argomenti nel subforum CORSI e fare una diagnosi preliminare basata sul contenuto di questi corsi.
  4. È VIETATO caricare diagrami completi, file BIOS / firmware o qualsiasi altro tipo di documentazione (o collegarsi a siti Web con tali file). Puoi caricare solo una piccola parte della documentazione o collegarti al file del BIOS nel subforum BIOS FILE NON VERIFICATI. Non è consentito caricare più di una pagina completa di istruzioni/diagrami per singolo argomento. Il file che carichi non deve contenere filigrane, contrassegni "Riservati", link o indirizzi email e non può essere protetto da password.
  5. È consentito descrivere un solo dispositivo difettoso per singolo argomento - dovresti sempre aprire un nuovo argomento per ogni dispositivo successivo.
  6. La richiesta degli diagrami completi, dei file BoardView, dei file BIOS o di qualsiasi altro tipo di documentazione NON È CONSENTITA in questo subforum. Se hai bisogno di chiedere uno di questi, dovresti aprire un nuovo argomento nel subforum DOCUMENTAZIONE E RICHIESTA BIOS/EFI.

#1 Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 4 settembre 2025, 19:14
Witam,

Dostałem do sprawdzenia laptopa Dell Latitude 7400 (LA-G871P Rev 1.0), który został zalany przez deszcz wpadający przez okno (zostawiony przy oknie). Zalanie sięgało w okolicach pamięci RAM oraz gniazda LVDS (klient zgłaszał, że laptop działał normalnie, tylko nie było podświetlenia). Po oczyszczeniu i weryfikacji spalone były 2 bezpieczniki od podświetlenia. Mierząc rezystancje na obu końcach punktów lutowniczych bezpieczników nie stwierdzono niskich oporności co by świadczyło o zwarciu. Po wymianie bezpieczników podświetlenie matrycy wróciło. Po zrobieniu reinstalacji systemu laptop został zwrócony. Po kilku dniach laptop powrócił z tym samym problemem, czyli braku podświetlenia. Ponowna weryfikacja bezpieczników nie wykazała ich spalenia i po ponownym skręceniu laptopa podświetlenie wróciło. Laptop był testowany kilka godzin i nie było żadnych objawów. Znów po pewnym czasie został zwrócony na brak podświetlenia. Czym to może być spowodowane?

Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da Google Adsense [BOT] 4 settembre 2025, 19:14

#2 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 4 settembre 2025, 21:34
Hello!

Please, post clear pictures of flooded areas of the board in its current state.

#3 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da Vogelek23 6 settembre 2025, 12:12
Otwórz obudowę matrycy i - oczywiście po odłączeniu baterii głównej - sprawdź, czy gniazdo lub wtyk kabla matrycy od strony ekranu nie są skorodowane.

iT0mT0m ha scritto:spalone były 2 bezpieczniki od podświetlenia
Dwa? :wtf: To znaczy które konkretnie (Fxx)? Bo od podświetlenia jest na tej płycie tylko jeden bezpiecznik.

#4 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 6 settembre 2025, 12:46
matic ha scritto:Hello!

Please, post clear pictures of flooded areas of the board in its current state.

Immagine
Immagine
Immagine

Nie było tutaj konkretnie, aby woda stała czy coś tylko były lekkie zacieki w tym obszarze. Ciecz dotarła nawet do jednej z kości pamięci RAM, ale o dziwno działa poprawnie.

Vogelek23 ha scritto:Otwórz obudowę matrycy i - oczywiście po odłączeniu baterii głównej - sprawdź, czy gniazdo lub wtyk kabla matrycy od strony ekranu nie są skorodowane.

Nie było nic skorodowane. Prewencyjnie przeczyściłem gniazda, aby mieć pewność, że nic tam nie było.

Vogelek23 ha scritto:Dwa? To znaczy które konkretnie (Fxx)? Bo od podświetlenia jest na tej płycie tylko jeden bezpiecznik.

Spalony był FV1 +BL_PWR_SRC oraz FV2 +TS_PWR. Napisałem dwa, ponieważ obydwa idą do gniazda matrycy wg boardview.

#5 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da Vogelek23 6 settembre 2025, 13:31
Podstaw 100% sprawną, przetestowaną matrycę.

#6 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 6 settembre 2025, 18:07
Niestety takiej nie posiadam. Musiałbym zamówić. Mogę coś jeszcze sprawdzić zanim bym ją zamawiał?

#7 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 7 settembre 2025, 18:16
Measure the voltages to ground on the following points, when the machine is turned on with the internal matrix connected:
- On pin 2 of resistor RC2.
- On pin 2 of fuse FV1.
- On pin 1 of coil LV1.
- On pin 1 of diode DV2.

#8 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 14 settembre 2025, 10:47
matic ha scritto:Measure the voltages to ground on the following points, when the machine is turned on with the internal matrix connected:
- On pin 2 of resistor RC2.
- On pin 2 of fuse FV1.
- On pin 1 of coil LV1.
- On pin 1 of diode DV2.


RC2 pin 2 - After connect power supply 2.5V. After power on button voltage is 0.016V.
FV1 pin 2 - After connect power supply 13.5V. After power on button voltage is get down.
LV1 pin 1 - Always 0V. Once after power on button voltage is 1.074V.
DV2 pin 1 - 0V after power on.

#9 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 14 settembre 2025, 12:32
Measure the voltages to ground on pins 1, 2 of transistor QV2, when the machine is turned on with the internal matrix connected.
Transistor QV2 pinout:
Immagine

#10 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 14 settembre 2025, 12:43
QV2 pin 1 - before power on - 13.1V, after power on - 0V
QV2 pin 2 - before power on - 0V, after power on - 3.3V

#11 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 15 settembre 2025, 08:34
Measure the voltages to ground on pins 1, 3, 4 of transistor QV1, when the machine is turned on with the internal matrix connected.

#12 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 15 settembre 2025, 17:23
matic ha scritto:Measure the voltages to ground on pins 1, 3, 4 of transistor QV1, when the machine is turned on with the internal matrix connected.


QV1 pin:
1 - 13.5V
3 - 2.007V
4 - 13.5V

#13 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 16 settembre 2025, 07:56
Remeasure the voltages suggested in post #7, when the machine is turned on with the internal matrix connected.

#14 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 18 settembre 2025, 19:29
matic ha scritto:Remeasure the voltages suggested in post #7, when the machine is turned on with the internal matrix connected.

- On pin 2 of resistor RC2 2,505V
- On pin 2 of fuse FV1 - 13,51V
- On pin 1 of coil LV1 - 1,174V
- On pin 1 of diode DV2 - 0,639V

#15 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 19 settembre 2025, 15:53
- Set your multimeter to the diode mode range and measure the voltage drops to ground on all pins of diode DV2 with the positive (red) probe connected to ground.
- Measure the voltages to ground on pins 2, 3 of diode DV2, when the machine is turned on with the internal matrix connected.

Diode DV2 pinout:
Immagine

#16 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 20 settembre 2025, 20:38
matic ha scritto:- Set your multimeter to the diode mode range and measure the voltage drops to ground on all pins of diode DV2 with the positive (red) probe connected to ground.

1 - 0.018V
2 - 0.760V
3 - 0.804V

matic ha scritto:- Measure the voltages to ground on pins 2, 3 of diode DV2, when the machine is turned on with the internal matrix connected.

2 - 0.002V
3 - 1.058V
Measured while show image on screen without backlight.

#17 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 22 settembre 2025, 08:29
Also measure the resistance to ground on pin 1 of diode DV2 with the internal matrix connected.

#18 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 22 settembre 2025, 21:32
matic ha scritto:Also measure the resistance to ground on pin 1 of diode DV2 with the internal matrix connected.

14.8Ω

#19 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da matic 23 settembre 2025, 09:35
This resistance is way too low.
It's most likely caused by a damaged LCD matrix or LVDS cable.

Remeasure this resistance with the LVDS cable disconnected from the board. If the resistance increases to a high value (in the kΩ range or greater), measure the resistance again with the LVDS cable connected and LCD matrix disconnected.
If the resistance with LCD matrix disconnected and LVDS cable connected is still high (in kΩ range or greater), the LCD matrix is definitely damaged and needs to be replaced.

#20 Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da iT0mT0m 23 settembre 2025, 19:54
Without LVDS cable I have 14.9Ω resistance on pin 1 of DV2.

Re: Dell Latitude 7400 - brak podświetlenia po zalaniu


da Google Adsense [BOT] 23 settembre 2025, 19:54

Chi c’è in linea

Visitano il forum: Nessuno e 9 ospiti

_______________________________
Tutti i diritti riservati. È severamente vietata la copia non autorizzata del contenuto di questo sito Web o di qualsiasi sua parte.
Eventuali marchi, nomi di società, prodotti o servizi pubblicati su questo sito Web appartengono ai legittimi proprietari, sono protetti da copyright e utilizzati solo a scopo informativo.