• Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v

Zasady działu:Kliknij, aby przejrzeć zasady tego działu

  1. Tytuł wątku powinien zawierać markę i pełny model sprzętu oraz skrótowy opis usterki.
  2. Treść wątku powinna zawierać dokładny opis usterki, co zostało sprawdzone/wymienione/zmierzone, wyniki tych działań, oznaczenie kodowe płyty głównej (w przypadku napraw hardware) oraz sformułowane pytanie. W przypadku problemów z odczytaniem oznaczenia kodowego płyty, należy przeczytać TEN WĄTEK. Jeśli nadal nie możesz znaleźć oznaczenia, powinieneś zamieścić wyraźne zdjęcia obu stron płyty - należy przy tym usunąć wszelkie folie i moduły, mogące ewentualnie zasłaniać oznaczenia płyty.
  3. Przed napisaniem nowego tematu, każdy użytkownik zobowiązany jest zapoznać się z wątkami w dziale SZKOLENIA i na ich podstawie dokonać próby wstępnej diagnostyki uszkodzenia.
  4. Nie jest dozwolone umieszczanie załączników w postaci kompletnych dokumentacji, a także wsadów BIOS (do tego służy dział PLIKI BIOS DO WERYFIKACJI). Dozwolone jest wyłącznie umieszczenie fragmentu dokumentacji, który ułatwi autorowi diagnostykę/naprawę sprzętu z wątku. W jednym poście można zamieścić nie więcej, niż jedną stronę instrukcji/schematu. Plik nie może posiadać widocznych znaków wodnych, napisów "confidential", adresów email etc.
  5. Nie jest dozwolone zamieszczanie linków do plików, znajdujących się na innych stronach internetowych.
  6. Nie jest dozwolone zakładanie tematu, który opisuje usterkę więcej niż jednego sprzętu. W takich przypadkach należy utworzyć osobne wątki dla każdego sprzętu.
  7. Nie jest dozwolone pisanie tematu lub postu, mającego charakter zapytania o schemat, boardview, zdjęcia płyty, wsad BIOS lub instrukcję serwisową. Do takich zapytań służy dział ZAPYTANIA O DOKUMENTACJE/BIOS.

#21 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 12 kwietnia 2018, 14:37
use isopropyl tips and found found hot UL1 (it is probably sound card). Desoldered it, and now have 260 KOhm on PJ303.

Are you sure KBC is faulty and need to replace with UL1?

Re: Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez Google Adsense [BOT] 12 kwietnia 2018, 14:37

#22 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 12 kwietnia 2018, 14:53
The resistance seems to be ok now.

Yes, both chips are bad for sure - with the KBC chip the resistance to ground on PJ303 was 2Ω, without it 10Ω.

Now remove the jumper PJ303, connect the power supply and check, if you get 3.3V on coil PL303 and 5V on coil PL304. If yes, replace both damaged chips.

#23 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 13 kwietnia 2018, 06:10
matic napisał(a):The resistance seems to be ok now.

Yes, both chips are bad for sure - with the KBC chip the resistance to ground on PJ303 was 2Ω, without it 10Ω.

Now remove the jumper PJ303, connect the power supply and check, if you get 3.3V on coil PL303 and 5V on coil PL304. If yes, replace both damaged chips.


PJ303 removed, but no 3,3 and 5v on coils... Are you sure this voltages will start without KBC?

#24 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 13 kwietnia 2018, 07:21
igore napisał(a):PJ303 removed, but no 3,3 and 5v on coils... Are you sure this voltages will start without KBC?
Sorry, my fault.
3.3V should be present on pin 5 of PU904.
5V shold be present on pin 5 of PU905.

To enable the 3,3V and 5V on coils PL303 and PL304 you could bridge the pins 1 and 5 of PU904 for the test. Do that with removed jumpers PJ303 and PJ303. If both voltages are ok, solder all jumpers back to the place and replace the KBC chip.

Edit:
By the way, this KBC chip is programmed. If you replaced it with brand new one (never used before) it should program itself at first connecting power supply to the board. It takes some time, so after connecting the power supply wait 15 minutes before pressing any button or disconnecting the power supply.

#25 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 13 kwietnia 2018, 07:40
matic napisał(a): Sorry, my fault.
3.3V should be present on pin 5 of PU904.
5V shold be present on pin 5 of PU905.


PU904 - PIN 5 - 3,3v
PIN 6 - 2,8

PU905 PIN5 - 3,3v
PIN6 - 2,8v
PIN 7 - 5,15v

It is OK?

#26 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 13 kwietnia 2018, 08:12
PU904 - PIN 5 - 3,3v
PIN 6 - 2,8

PU905 PIN5 - 3,3v
PIN6 - 2,8v
PIN 7 - 5,15v

It is OK?
Yes, voltages seems ok. Now you could try to enable the 3.3V and 5V on coils PL303 and PL304, as I mentioned in previous post.

#27 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 13 kwietnia 2018, 08:37
You are right - bridge pins 1 and 5 PU904 and on coils are 3,3 and 5v. I need to order KBC and Realtek. Let you know soon.

#28 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez Type5 13 kwietnia 2018, 11:20
igore napisał(a):UL1 (it is probably sound card).
UL1 to RTL8111GUL - karta LAN.

#29 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 16 kwietnia 2018, 11:19
matic napisał(a):
Yes, voltages seems ok. Now you could try to enable the 3.3V and 5V on coils PL303 and PL304, as I mentioned in previous post.


I replaced KBC and LAN card, now have ON PJ303 - 3,15 KOhm and on PJ306 - 70 KOhm.

Let ma know about programming new KBC - motherboard need to start with RAM module?

#30 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 16 kwietnia 2018, 11:41
igore napisał(a):Let ma know about programming new KBC - motherboard need to start with RAM module?
As I said, the KBC chip should program itself at first connecting power supply to the board. This should work, only if you bought brand new KBC chip (never used before).
Just solder everything to the board, connect the RAM memory and the power supply. Then wait about 15 minutes. After that you could try to turn on the laptop by pressing to the power button.

If you have a known good BIOS dump you could reflash the BIOS chip before connecting the power supply.

#31 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 16 kwietnia 2018, 13:18
have bad news - i soldered KBC turned 180° :(

Can i solder properly? Or need new one?

#32 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez Type5 16 kwietnia 2018, 13:26
Nie powinien się uszkodzić, bo wszystkie napięcia koło niego to 3,3V.
Wlutuj poprawnie.

#33 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 16 kwietnia 2018, 14:31
Type5 napisał(a):Nie powinien się uszkodzić, bo wszystkie napięcia koło niego to 3,3V.
Wlutuj poprawnie.


OK wlutowałem poprawnie - podpiąłem płytę pod zasilacz serwisowy, zaświeciła się dioda oznaczona LED4, prąd 0,2A - i tak czekałem 20 min.

PO tym czasie próbuje załączyć płytę - ale nic się nie dzieje.
3,3v/5v jest poprawne. Na włączniku jest 3,3v

Chyba jednak uwaliłem ten KBC? Co jeszcze mogę zrobić/sprawdzić?

#34 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 16 kwietnia 2018, 15:09
igore napisał(a):podpiąłem płytę pod zasilacz serwisowy
Have you used appropriate cable with the connected central pin?
If yes, do the following measurements:

Measure the voltages to ground on pins 14, 72, 74, 108 of KBC chip.

Measure the voltages to ground on pins 18, 21, 93 of KBC chip in the following cases:
a) Before pressing to the power button.
b) After pressing to the power button.

Measure the voltages to ground on pins 76, 86 of KBC chip in the following cases:
c) Power button released.
d) Power button pressed.

#35 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 17 kwietnia 2018, 08:05
yes i have cable with central connected pin (1,5 KOhm between + and central). Checked with original adapter too

Here are measurments of KBC:

PIN 4 - 0,9v
72 - 0,08v
74 - 3,3v
108 - 0v

PIN - 18 before pressing 0v / after pressing 0v
21 0v/0v
93 3,3v/3,3v

PIN -76 pwr released 3,18v / pressed 3,18v
86 3,3v / 3,3v

#36 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 17 kwietnia 2018, 08:59
Measure the voltages to ground on both pins of resistor PR322.

Measure the voltages to ground on pins 1 and 2 of diode D15 in the following cases:
a) Power button released.
b) Power button pressed.

Diode D15 pinout:
Obrazek

#37 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 17 kwietnia 2018, 09:34
D15

PIN1 - pressed 3,16 / released 3,26
PIN2 - 3,22 / 3,22

Can you let me know where is PR322 ? - i have no board view

#39 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez matic 17 kwietnia 2018, 09:57
PR322 is located under the DC socket "JDCIN1" (on the other side of the board).
Obrazek

Measure the voltage on the power button in the following cases:
a) Power button released.
b) Power button pressed.

#40 Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez igore 17 kwietnia 2018, 10:34
Machine napisał(a):Measure the voltages on pin 110 of the KBC in the following cases:
at the power off
with pressed power on
to the power on.


at the power off - 3,3 v
with pressed power on - 3,3v
to the power on - 3,3v

Pwr Button:

released - 3,3
pressed - 0v

PR322:
Obrazek

Re: Lenovo Z50-70 płyta ACLUA/ACLUB NM-A273 - brak 3,3v


przez Google Adsense [BOT] 17 kwietnia 2018, 10:34

Kto przegląda forum

Użytkownicy przeglądający ten dział: Brak zidentyfikowanych użytkowników i 1 gość

_______________________________
Wszelkie prawa zastrzeżone. Zabrania się kopiowania jakichkolwiek treści i elementów witryny bez zezwolenia.
Wszelkie opublikowane na tej stronie znaki handlowe, nazwy marek, produktów czy usług należą do ich prawnych właścicieli i zostały użyte wyłącznie w celach informacyjnych.